Schluter®-BARA-RWL

Edging profile with drainage holes for large-format pavers

Schluter®-BARA-RWL is a color-coated aluminum edging profile with drainage holes for the perimeters of balconies and terraces where large-format pavers are installed over loose-laid gravel or elevated sub-structures.
  • Designed for the perimeters of balconies and terrace coverings loose-laid on gravel or elevated sub-structures
  • Anchoring leg is available with a special radius perforation so that the profile can be used to form curves
  • Available in color-coated aluminum
 ...read more  ...show less

Product type

Select all options to find the
specific product you want to buy.

Find recommended accessories here

Schluter®-BARA-RWL is a color-coated aluminum, L-shaped finishing profile for large-format pavers that are laid on loose gravel layers or stilted assemblies above a waterproofing layer and drainage layer. The trapezoid-perforated anchoring leg of BARA-RWL is placed along the edge, on top of the waterproofing layer, and adjusted to the proper height and alignment. The vertical finishing leg covers the edge of either the entire surface assembly or just the gravel layer or stilts. Profile heights from 9/16" to 5-29/32" (15 to 150 mm) allow for any type of edge formation. Drainage holes, spaced at approximately 2-15/16" (75 mm), are incorporated at the transition of the anchoring leg and the finishing leg to ensure the proper drainage of any collecting seepage water.

BARA-RWL is available with a special radius perforation “R” so that the profile can be used to form curves.

BARA-RWL requires no special maintenance or care. The coatings on the color-coated aluminum profile are colorfast and UV-resistant. Damaged surfaces shall be painted over.

1. Select BARA-RWL according to the height of the floor construction to be covered. Prefabricated corners and connectors are available for inside and outside corners. Abut the profile ends of BARA-RWL, leaving an approx. 3/16" (5 mm) joint. Cover the joint with the clip-on connector.

2. Before the TROBA-PLUS drainage membrane is installed, set the trapezoid-perforated anchoring leg of the finishing profile, BARA-RWL, onto the waterproofing layer and, if required, adjust to the proper height and alignment with dots of mortar.

3. If BARA-RWL is used as a gravel edge profile, the gravel layer should abut the vertical profile leg just below the upper lip. The concrete pavers are laid loosely on top of the leveled gravel layer.

4. If BARA-RWL is used as a finishing profile in conjunction with stilted floor coverings, the profile covers the exposed edge of the covering assembly. The support pedestals are laid on top of the trapezoid-perforated anchoring leg of BARA-RWL. The concrete pavers are then set onto the pedestals.

Note: To ensure unobstructed drainage at the edge areas of the covering, make certain during installation that drainage openings in the drainage membrane and profile and that spaces between the pedestals remain open.

Product Table

11202-preview
19.55 KB
BalconyProfiles_GutterSystems
898.52 KB
Pdf

Warranties

BalconyandTerrace-Profiles-Warranty
57.34 KB
Pdf

Data sheets

Balcony and Terraces Data Sheet
1.12 MB
Pdf
Q:

How do I cut profiles?

A:

Schluter™ profiles are available in a variety of different materials , so methods for cutting vary. Below are best practices for cutting according...

Read more

Spec. Guides

Product Spec Guide 2019
1.25 MB
Pdf

CAD drawings

schlueter_cad_bara_rwl_inst
42.92 KB
DWG
schlueter_cad_bara_rwl_imp
46.55 KB
DWG
schlueter_cad_bara_rwl_imp
4.11 KB
Pdf
schlueter_cad_bara_rwl_metr
33.37 KB
DWG
schlueter_cad_bara_rwl_metr
3.95 KB
Pdf

Specify our products using the

Specification Logo