Schluter FAST-SET™

Schluter FAST-SET™ is a specialized rapid-setting modified thin-set mortar specifically formulated for use with Schluter® membranes and boards.

  • Engineered for use both under and over all DITRA and KERDI products
  • Ready to grout in 4 hours for fast-track projects
  • Sag-resistant, smooth and creamy
  • Easy to handle and spread
  • Suitable for use with ceramic, porcelain, and stone tile, including large and heavy tile
  • To be used in conjunction with Schluter®-Systems’ uncoupling and waterproofing membranes (DITRA, DITRA-HEAT, and KERDI), the Schluter®-Shower System, and KERDI-BOARD
  • Meets ANSI A118.4TF, ANSI A118.11, & ANSI A118.15TF
  • Available in gray and white
  • Lifetime warranty when used with applicable Schluter® products
Read more

Schluter FAST-SET™ is a specialized rapid-setting modified thin-set mortar specifically formulated for use with Schluter® membranes and boards.

  • Engineered for use both under and over all DITRA and KERDI products
  • Ready to grout in 4 hours for fast-track projects
  • Sag-resistant, smooth and creamy
  • Easy to handle and spread
  • Suitable for use with ceramic, porcelain, and stone tile, including large and heavy tile
  • To be used in conjunction with Schluter®-Systems’ uncoupling and waterproofing membranes (DITRA, DITRA-HEAT, and KERDI), the Schluter®-Shower System, and KERDI-BOARD
  • Meets ANSI A118.4TF, ANSI A118.11, & ANSI A118.15TF
  • Available in gray and white
  • Lifetime warranty when used with applicable Schluter® products
Configure to Price Add to
Project
Dealer
Locator
Product
Table

Product successfully added to Project List

You can now access your Project List or stay on this page

Go to Project List Continue browsing

Uppsss...

Sorry, something went wrong. Please try again later.

Continue browsing
Share
Schluter FAST-SET™

Schluter FAST-SET™

Specialized Rapid-setting Modified Thin-set Mortar
Schluter FAST-SET™
Schluter FAST-SET™
Schluter FAST-SET™
Schluter FAST-SET™
Schluter FAST-SET™
Schluter FAST-SET™
Schluter FAST-SET™

Product type

Next
Schluter FAST-SET™

Schluter FAST-SET™ is a specialized, fast-setting modified thin-set mortar for use as a bond coat within tile assemblies that is optimized for use with Schluter® membranes and boards. Schluter FAST-SET™ is smooth and creamy, as well as easy to handle and spread. It is sag-resistant and ideal for setting tile on both horizontal and vertical surfaces. Schluter FAST-SET™ is suitable for use with ceramic, porcelain, and stone tile, including large and heavy tile, in conjunction with Schluter®-Systems’ uncoupling and waterproofing membranes (e.g., DITRA, DITRA-HEAT, KERDI, etc.), the Schluter®-Shower System, and KERDI-BOARD. Schluter FAST-SET™ can be used in both interior and exterior systems and is available in both grey and white.

For complete installation guidelines and warranty criteria, please download the appropriate Schluter® Installation Handbook and view the installation videos available below.

Materials must be acclimated to ambient conditions and installed when the ambient and surface temperatures are within a range of 40°F (4°C) to 95°F (35°C). Tenting of working area may be necessary to shade the surfaces from direct sunlight and/or rain. Direct sunlight or high temperatures may cause flash setting or skinning of the mortar. If an installation is to be completed in cold temperatures, the space must be heated before, during and after the installation to ensure proper curing of the mortar. Combustion heaters must be vented for carbon monoxide safety.

Surface Preparation

1. The substrate must be clean, even, and load bearing. Any leveling of the subfloor must be done prior to application of Schluter FAST-SET™.

2. For concrete substrates, remove any waxy or oily films and curing compounds (if present) by mechanical scarification (take steps to not to breath in any residual dust).

3. When bonding to particularly dry, porous concrete, the slab should be moistened to saturate the concrete and help prevent premature drying or skinning of the bond coat. Excess or standing surface water must be removed prior to installation.

4. For gypsum substrates, residual moisture in gypsum screed must be 2.0% or less before installing Schluter® uncoupling membranes. Follow gypsum manufacturer’s directions for additional substrate preparation.

Mixing

1. Put clean, potable water into a clean pail. Slowly add powder while beginning to mix. Use 5.5 - 6.5 qts (5.2 - 6.2 L) of water to 50 lbs (22.7 kg) of mortar. Mix at a slow speed (<300 rpm) for 5 minutes.

2. Following this procedure will produce the best workability and help ensure maximum open time and pot life. For Schluter® membranes the mortar should be mixed to a fairly fluid consistency, but still able to hold a notch. Do not add more water after mixing.

Application

To substrate:

1. Apply a thin layer of the mortar with the flat side of the trowel to produce solid contact with the substrate.

2. Using an appropriate sized notched trowel, comb additional mortar using the notched side of the trowel. Mortar ridges should run in one direction.

3.

a. Schluter®-DITRA family of uncoupling membranes:

Solidly embed into the mortar using a float, screed trowel, or SchluterR-DITRA-ROLLER. When using DITRA-ROLLER, place a weight (e.g., bag(s) of mortar/grout or box of tile) not to exceed 75 lbs (34 kg) on the DITRA-ROLLER shelf. Slowly move the roller from one end of the matting to the other, slightly overlapping successive passes. Lift up a corner of the membrane to check coverage. Proper installation results in full contact between the fleece webbing and the mortar.

b. Schluter®-KERDI family of waterproofing membranes:

Solidly embed into the mortar using the flat side of the trowel or a drywall finishing knife and work the membrane onto the entire surface to ensure full coverage and remove air pockets. Lift up a corner of the membrane to check coverage. Proper installation results in full contact between the fleece webbing and the mortar.

c. Tile:

Solidly embed the tile in the mortar, pushing the tile in a back and forth motion to collapse the mortar ridges. Periodically remove and check tile to ensure sufficient coverage is being attained (>80% for dry applications, >95% for exterior or shower applications –see ANSI A108.5). Back-buttering is a useful way to help ensure proper coverage, particularly when installing 12" x 12" (305 mm x 305 mm) and larger tiles. Clean all excess mortar from tile and joints while mortar is still plastic using a sponge and clean water.

4. Make sure to observe the open time of the thin-set mortar. If the mortar skins over, remove and re-apply fresh mortar.

To DITRA or KERDI products:

1.

a. Schluter®-DITRA family of uncoupling membranes: Completely fill the cavities in the membrane.

b. Schluter®-KERDI family of waterproofing products: Apply a thin layer of the mortar with the flat side of the trowel to produce solid contact with the fleece.

2. Using an appropriate sized notched trowel, comb additional mortar using the notched side of the trowel. Mortar ridges should run in one direction.

3. Solidly embed the tile in the mortar, pushing the tile in a back and forth motion to collapse the mortar ridges.

4. Using care not to release the membrane from the substrate, periodically remove and check tile to ensure sufficient coverage is being attained (>80% for dry applications, >95% for exterior or shower applications – see ANSI A108.5). Back-buttering is a useful way to help ensure proper coverage, particularly when installing 12" x 12" (305 mm x 305 mm) and larger tiles.

5. Make sure to observe the open time of the thin-set mortar. If the mortar skins over, remove and re-apply fresh mortar.

6. Clean all excess mortar from tile and joints while mortar is still plastic using a sponge and clean water.

Clean Up

Clean tools with water while mortar is plastic.

Curing and Grouting

Maintain ambient and surface temperatures between 40°F to 95°F (4° C to 35° C). Wait at least 4 hours at 70° F (21° C) before grouting. Extended cure times before and after grout application may be required if temperatures are lower. Install grout per ANSI A108.10, A108.9 or A108.6 specifications and grout manufacturer’s instructions. Protect the installation from heavy traffic and water exposure for a minimum of 24 hours to allow the mortar to set. Protect the installation from freezing for a minimum of 28 days.

Shelf Life and Storage: 1 year from the date on the side of the bag if unopened and stored off the ground in a dry area protected from the weather.

FAQ

Architectural Material

Spec. Guides

Specify our products using the Specification Logo

Watch & Learn about this product

/

Schluter ALL-SET™

Setting Materials

Schluter ALL-SET™

Specialized Modified Thin-set Mortar

Schluter®-DITRA & DITRA-XL

Uncoupling (DITRA)

Schluter®-DITRA & DITRA-XL

Uncoupling and waterproofing membrane

Schluter®-KERDI

Waterproofing (KERDI)

Schluter®-KERDI

Bonded waterproofing and vapor-retardant membrane

Schluter®-DITRA-HEAT

Floor Warming

Schluter®-DITRA-HEAT

Uncoupling membrane specifically designed for DITRA-HEAT-E-HK electric floor heating cables

Schluter®-KERDI-BOARD

KERDI-BOARD Panels

Schluter®-KERDI-BOARD

Waterproof, multifunctional tile substrate and building panel

Schluter®-KERDI-SHOWER-KIT

KERDI-SHOWER-KIT

Schluter®-KERDI-SHOWER-KIT

Complete shower kit

Schluter®-TROWEL

Tools

Schluter®-TROWEL

Square-notched trowel

Schluter®-KERDI-TUBKIT

KERDI-TUBKIT

Schluter®-KERDI-TUBKIT

Complete bathtub surround kit

Schluter®-DITRA-HEAT-DUO

Floor Warming

Schluter®-DITRA-HEAT-DUO

Uncoupling membrane with integrated sound control and thermal break