Schluter®-BARA-RTP

Schluter®-BARA-RTP is a retrofit edging profile made of color-coated aluminum, which is designed to integrate with the BARIN gutter system.

  • Can be retrofitted to the exposed edges of existing balconies and terraces
  • 90° inside corners, and 90° and 135° outside corners are available
  • Available in color-coated aluminum
Read more

Schluter®-BARA-RTP is a retrofit edging profile made of color-coated aluminum, which is designed to integrate with the BARIN gutter system.

  • Can be retrofitted to the exposed edges of existing balconies and terraces
  • 90° inside corners, and 90° and 135° outside corners are available
  • Available in color-coated aluminum
Configure to Price Add to
Project
Dealer
Locator
Product
Table

Product successfully added to Project List

You can now access your Project List or stay on this page

Go to Project List Continue browsing

Uppsss...

Sorry, something went wrong. Please try again later.

Continue browsing
Share
Schluter<sup class='regsign'>®</sup>-BARA-RTP

Schluter®-BARA-RTP

Retrofit edging profile for balconies and terraces
Schluter®-BARA-RTP
Schluter®-BARA-RTP
Schluter®-BARA-RTP
Schluter®-BARA-RTP

Product type

Next

Schluter®-BARA-RTP is a color-coated aluminum edging profile that can be retrofitted to the exposed edges of existing balconies and terraces. A T-shaped chamber in the vertical leg of BARA-RTP is designed to accept the BARIN gutter system. BARIN is fastened to the balcony edging profile with screws. The screw slots in the gutter are elongated, making it possible to slope the gutter up to 1-3/16" (30 mm).

Matching inside corners, outside corners, and connector pieces are available for BARA-RTP.

1. To fasten the BARA-RTP edging profile, drill 5/16" (8 mm)-diameter holes into the fascia at approximately 20" (50 cm) intervals. To align with the holes provided in the profile, BARA-RTP can be placed against the fascia and used as a drilling template.

2. After inserting the anchors, the BARA-RTP edging profile should be fastened with BARA-RTPS 540 special bolts (provided). To properly fasten BARA-RTP to the fascia, it is advisable, beforehand, to fill the rear section of the edging profile with thin-set mortar.

3. Once BARA-RTP has been mounted, the BARIN gutter system can be attached. To do this, fasten the BARIN gutter to the BARA-RTP edging profile with screws. BARIN features slotted holes for establishing the proper slope.

4. Please note: Prefabricated corners and connectors are available for inside corners, outside corners, and butt joints. Abut the ends of BARA-RTP, leaving an approx. 3/16" joint. Cover the joint with the clip-on connector.

BARA-RTP requires no special maintenance or care. The coatings on the color-coated aluminum profile are colorfast and UV-resistant. Damaged surfaces shall be painted over.

Downloads

Warranties

Data sheets

FAQ

Architectural Material

Specify our products using the Specification Logo

/

Schluter®-BARA-RTK

Balcony profiles

Schluter®-BARA-RTK

Edging profile for balconies and terraces

Schluter®-BARA-RAK

Balcony profiles

Schluter®-BARA-RAK

Balcony edging profile with drip lip

Schluter®-BARIN-SR

Gutter Systems

Schluter®-BARIN-SR

Gutter system for balconies and terraces

Schluter®-BARA-RAKE

Balcony profiles

Schluter®-BARA-RAKE

Balcony edging profile with drip lip and drainage holes for Schluter-DITRA-DRAIN applications